MOTU 896HD User's Guide Page 95
- Page / 105
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
CUEMIX CONSOLE
95
Viewing a mix
To v ie w a m i x, click its tab at the bottom of the
window, as shown in Figure 12-1. The mix name
appears in the tab.
Naming a mix
Double-click the mix name in the tab.
Master mute
The master mute button (Figure 12-1) temporarily
disables (silences) the mix.
Master fader
The master fader (Figure 12-1) controls the overall
level of the mix (its volume on its stereo output).
Use the individual input faders to the left to control
individual input levels.
Adjusting master faders from the front panel
Yo u c a n a d j u s t t h e master fader level for each mix
using the MONITOR LEVEL knob on the 896HD
front panel. When you turn it, the analog input
meters (channels 1-4) temporarily display the
current volume setting for each mix. A few seconds
after you stop turning (or pushing) the knob, the
meters revert back to displaying analog input
levels.
The MONITOR LEVEL knob controls each
CueMix master fader as follows:
When using the MONITOR LEVEL knob to view
and modify the CueMix master fader levels, the
8-channel bank of programmable meters (to the
right of the analog input meters) displays the
output level for each mix bus as follows:
Output level meters
The OUT level meters show you the output for the
mix’s physical output, which may include audio
from your host audio software. The clip indicators
clear themselves after a few seconds.
Input section
The channel strips to the left of the master fader
represent each input in your 896HD. Use the input
scroll bar to view additional inputs.
Input mute/solo
To a d d a n i n put to a mix, or remove it, click its
MUTE button. To solo it, use its SOLO button. To
toggle these buttons for a stereo pair, hold down
the command key while clicking either channel.
The Solo indicator LED (Figure 12-1) lights up
when any input is soloed (including inputs that
may currently be scrolled off-screen).
Input volume and pan
Use the input fader and pan knob (Figure 12-1) to
adjust these settings for the input in the mix. Again,
all settings within the gray-shaded channel strip
area belong to the mix currently being viewed.
Note that an input can have different settings in
different mixes.
To a d j u s t t he vo lu me or panning for a stereo input
pair, hold down the command key while dragging
the fader or knob for either the left or right input.
Action Result
Push the knob To view the current fader levels for all
four CueMix busses.
Turn the knob To adjust the currently selected fader.
(This is indicated by a flashing red
“over” LED at the top of the meter.)
Push the knob again To cycle to the next mix bus. The
flashing red “over” LED shows you
which bus you are adjusting.
Programmable meter channels Mix bus
1-2 Mix1
3-4 Mix2
5-6 Mix3
7-8 Mix4
- MOTU 896HD 1
- Contents 3
- Quick Reference: 7
- About the 896HD 9
- Connection Input Output 10
- Total 18 22 10
- THE 896HD FRONT PANEL 11
- 16-BIT AND 24-BIT RECORDING 12
- AUDIODESK 12
- DIGITAL PERFORMER 12
- OTHER HOST AUDIO SOFTWARE 12
- A COMPUTER-BASED SYSTEM 12
- Packing List and 13
- Macintosh System Requirements 13
- Installing the 896HD Hardware 15
- INSTALLING THE 896HD HARDWARE 16
- CONNECT A FOOT SWITCH 17
- USING THE 896HD WITH A MIXER 18
- MAKING SYNC CONNECTIONS 19
- DO YOU NEED A SYNCHRONIZER? 20
- SAMPLE-ACCURATE SYNC 21
- SAMPLE-ACCURATE ADAT SYNC 22
- SYNCHRONIZER 23
- Use this setup if you have: 24
- This setup provides: 24
- SYNCING OPTICAL DEVICES 25
- SYNCING AES/EBU DEVICES 26
- ■ Clock source 27
- ■ Sample rate conversion 27
- SYNCING WORD CLOCK DEVICES 29
- SYNCING LARGE SYSTEMS 30
- INTERFACES 31
- Software 33
- MOTU FireWire Audio Console 37
- (Mac OS X) 37
- 896HD SETTINGS 38
- ‘GENERAL’ TAB SETTINGS 43
- Performer 44
- MOTU FireWire Control Panel 45
- (Mac OS 9) 45
- Digital Performer 53
- DIGITAL PERFORMER 55
- TRIMMING THE ANALOG INPUTS 56
- 24-BIT OPERATION 56
- FINE-TUNING I/O TIMING 56
- SYNCHRONIZATION 57
- Performer documentation 59
- AudioDesk 61
- THE 896HD SETTINGS 62
- AUDIODESK 63
- AUDIODESK AND MIDI SEQUENCING 67
- Other Mac OS X Audio Software 69
- CHOOSING THE MOTU FIREWIRE 70
- COREAUDIO DRIVER 70
- AUDIO INPUT AND OUTPUT NAMES 71
- NUMBER OF CHANNELS 72
- USING A FOOT SWITCH 73
- OTHER MAC OS X AUDIO SOFTWARE 74
- Cubase, Nuendo and OS 9 ASIO 75
- PREPARATION 76
- THE ASIO CONTROL PANEL BUTTON 78
- ASIO DIRECT MONITORING 78
- OTHER SYSTEM DIALOG SETTINGS 79
- ACTIVATING 896HD INPUTS 79
- ASSIGNING INPUTS 80
- ASSIGNING OUTPUTS 81
- CHANGING 896HD SETTINGS 82
- Cubase VST 83
- MIDI MACHINE CONTROL (MMC) 84
- MONITORING SYSTEM PERFORMANCE 84
- Reducing Monitoring Latency 85
- MONITORING LIVE INPUT 86
- ■ Patch thru latency 88
- REDUCING MONITORING LATENCY 90
- REDUCING MONITORING LATENCY 91
- CueMix Console 93
- CUEMIX CONSOLE INSTALLATION 94
- WORKING WITH A MIX 94
- Action Result 95
- SHORTCUTS 96
- ENTIRE MIXES 96
- MESSAGE CENTER 96
- FILE MENU 96
- EDIT MENU 97
- PHONES MENU 97
- CONTROL SURFACES MENU 97
- STAND-ALONE OPERATION 99
- CUEMIX CONSOLE EXAMPLES 99
- CUEMIX CONSOLE 100
- Troubleshooting 101
- CUSTOMER SUPPORT 102
- REPLACING DISKS 102
- TECHNICAL SUPPORT 102
Related products and manuals for Recording Equipment MOTU 896HD
Recording Equipment MOTU 896 User's Guide
(76 pages)
(76 pages)
Autodesk Manuels des logiciels manuels d'utilisation
À partir de S
Comments to this Manuals