MOTU 828mkII User's Guide Page 19
- Page / 110
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
INSTALLING THE 828MKII HARDWARE
19
The optical jacks can be connected to either an
ADAT “lightpipe” device or an optical S/PDIF
“TOSLink” device. Just make the connections as
needed and then you’ll set the format later in the
MOTU FireWire Audio Console. Input and output
are independent. For example, you could connect
ADAT optical input from your digital mixer and
connect TOSLink optical output to your DAT deck.
Main outs
The main outputs serve as independent outputs.
The main out volume is controlled by the volume
knob on the front panel. Push the knob to toggle
between phone and main out volume control. In a
standard studio configuration, the main outs are
intended for a pair of studio monitors, but they can
also be used as additional outputs for any purpose.
CONNECT MIDI GEAR
828mkII MIDI input and output is supported
under Mac OS X only. Connect your MIDI device’s
MIDI IN jack to the 828mkII’s MIDI OUT jack
(Connection A below). Conversely, connect the
MIDI device’s MIDI OUT jack to the 8238mkII’s
MIDI IN jack (Connection B).
Figure 3-3: Connecting a MIDI device to the 828mkII.
One-way MIDI connections
MIDI devices that do not receive MIDI data, such
as a dedicated keyboard controller, guitar
controller, or drum pad, only need Connection B
shown in Figure 3-3. Similarly, devices that never
send data, such as a sound module, only need
Connection A. Make both connections for any
device that needs to both send and receive MIDI
data.
Connecting additional gear with MIDI THRUs
If you need to connect several pieces of MIDI gear,
run a MIDI cable from the MIDI THRU of a device
already connected to the 828mkII to the MIDI IN
on the additional device as shown below in
Figure 3-4. The two devices then share the
828mkII’s MIDI OUT port. This means that they
share the same set of 16 MIDI channels, too, so try
to do this with devices that receive on only one
MIDI channel (such as effects modules) so their
receive channels don’t conflict with one another.
Figure 3-4: Connecting additional devices with MIDI THRU ports.
CONNECT A FOOT SWITCH
If you would like to use a foot switch with your
828mkII, connect it to the PUNCH IN/OUT jack.
See “Quick Reference: MOTU FireWire Audio
Console” on page 7 for information about how to
program the foot switch to trigger any computer
keystroke you wish.
828mkII
rear panel
MIDI Device
MIDI
cables
MIDI
IN
MIDI
OUT
MIDI
OUT
MIDI
IN
Connection A
Connection B
MIDI IN
MIDI
cable
MIDI Device
MIDI
IN
MIDI
THRU
MIDI
OUT
Additional device
828mkII
rear panel
!828 Manual/Mac Page 19 Tuesday, May 27, 2003 1:45 PM
- MOTU 828mkII 1
- Contents 3
- Quick Reference: 7
- About the 828mkII 9
- Connection Input Output 10
- Total 20 22 10
- THE 828MKII FRONT PANEL 11
- 16-BIT AND 24-BIT RECORDING 12
- AUDIODESK 12
- DIGITAL PERFORMER 12
- OTHER HOST AUDIO SOFTWARE 12
- A COMPUTER-BASED SYSTEM 12
- ABOUT THE 828MKII 13
- ABOUT THE 828MKII 14
- Packing List and 15
- Macintosh System Requirements 15
- OVERVIEW 17
- CONNECT THE 828MKII INTERFACE 17
- CONNECT MIDI GEAR 19
- CONNECT A FOOT SWITCH 19
- MAKING SYNC CONNECTIONS 22
- DO YOU NEED A SYNCHRONIZER? 23
- SAMPLE-ACCURATE SYNC 24
- SAMPLE-ACCURATE ADAT SYNC 25
- SYNCHRONIZER 26
- SYNCING TO SMPTE TIME CODE 27
- CODE USING A SYNCHRONIZER 28
- SYNCING OPTICAL DEVICES 29
- SYNCING S/PDIF DEVICES 30
- SYNCING WORD CLOCK DEVICES 31
- SYNCING LARGE SYSTEMS 31
- INTERFACES 32
- Software 35
- Audio MIDI Setup 36
- MOTU FireWire Audio Console 41
- (Mac OS X) 41
- 828MKII SETTINGS 42
- MOTU FireWire Control Panel 47
- (Mac OS 9) 47
- 828mkII Front Panel Operation 53
- SETUP / SELECT 54
- To do this: Do this: 55
- CURSOR / VALUE 57
- STAND-ALONE OPERATION 57
- 828MKII FRONT PANEL OPERATION 58
- Digital Performer 59
- DIGITAL PERFORMER 61
- 24-BIT OPERATION 62
- FINE-TUNING I/O TIMING 62
- SYNCHRONIZATION 62
- MIDI MACHINE CONTROL (MMC) 63
- AudioDesk 65
- THE 828MKII SETTINGS 66
- AUDIODESK 67
- AUDIODESK AND MIDI SEQUENCING 71
- Other Mac OS X Audio Software 73
- CHOOSING THE MOTU FIREWIRE 74
- COREAUDIO DRIVER 74
- AUDIO INPUT AND OUTPUT NAMES 75
- NUMBER OF CHANNELS 76
- USING A FOOT SWITCH 77
- OTHER MAC OS X AUDIO SOFTWARE 78
- Cubase, Nuendo and OS 9 ASIO 79
- PREPARATION 80
- THE ASIO CONTROL PANEL BUTTON 82
- ASIO DIRECT MONITORING 82
- OTHER SYSTEM DIALOG SETTINGS 83
- ACTIVATING 828MKII INPUTS 83
- ASSIGNING INPUTS 84
- ASSIGNING OUTPUTS 85
- CHANGING 828MKII SETTINGS 86
- Cubase VST 87
- MONITORING SYSTEM PERFORMANCE 88
- Reducing Monitoring Latency 89
- MONITORING LIVE INPUT 90
- ■ Patch thru latency 92
- REDUCING MONITORING LATENCY 94
- REDUCING MONITORING LATENCY 95
- CueMix Console 97
- CUEMIX CONSOLE INSTALLATION 98
- WORKING WITH A MIX 98
- SHORTCUTS 99
- ENTIRE MIXES 99
- MESSAGE CENTER 99
- CUEMIX CONSOLE 100
- CUEMIX CONSOLE EXAMPLES 101
- MOTU SMPTE Console 103
- FRAME RATE 104
- READER SECTION 104
- GENERATOR SECTION 105
- MOTU SMPTE CONSOLE 106
- Troubleshooting 107
- CUSTOMER SUPPORT 108
- REPLACING DISKS 108
- TECHNICAL SUPPORT 108
Related products and manuals for Recording Equipment MOTU 828mkII
Recording Equipment MOTU 896 User's Guide
(134 pages)
(134 pages)
Recording Equipment MOTU 8pre User's Guide
(80 pages)
(80 pages)
Recording Equipment MOTU 896HD User's Guide
(105 pages)
(105 pages)
Recording Equipment MOTU 896 User's Guide
(76 pages)
(76 pages)
© 2020, manymanuals.com. All rights reserved. | 0.331 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals