MOTU Digital Timepiece Instruction Manual Page 110
- Page / 156
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
USING THE FRONT PANEL LCD
108
conform to standard practices. For example, some
samplers require Direct Connect mode in order to
perform sample dump transfers to and from the
Mac. If you have difficulty with sysex transfers, try
Direct Connect mode.
☛ Note: the MIDI device must be connected to a
MIDI IN and a MIDI OUT with the same number.
Use the VALUE knob to select the cable that the
device is connected to.
☛ Important note: when the MIDI
Timepiece AV is in Direct Connect mode, it cannot
receive or send data from any other ports except
the direct connect ports.
Direct Connect mode can only be turned on and
off with the front panel LCD.
Reset All Data
This window resets the MIDI Timepiece AV to its
factory default settings.
☛ BEWARE! When you reset all data, you lose
everything in memory, including all modifiers and
any modifications you have made to the base
setups.
PERFORMING A MIDI DATA DUMP
The DATA DUMP window (selected with the
WINDOW knob) causes the MIDI Timepiece AV
to transmit several system exclusive messages to
the computer and to output cable 1. These
messages contain a description of the current state
of the MIDI Timepiece AV at the time of the bulk
dump (not including modifiers and base setups
other than the current base setup).
To initiate the bulk dump, press ENTER.
Receiving a MIDI data dump
To get the MIDI Timepiece AV to receive a MIDI
data dump, transmit the data dump from software
running on the Mac, or transmit it from a
sequencer or other device connected to MIDI IN
number 8. The MIDI Timepiece AV is ready to
receive the dump at all times; no special
preparation is needed. The data dumps must be
received from either the computer port, the
network port, or MIDI IN cable 8.
USING THE SMPTE CONTROLS
Use the WINDOW knob to go to the SYNC
window. Make the SMPTE settings with the
CURSOR and VALUE knobs as follows:
SYNC
This window is for display only. It shows a running
update of the current SMPTE location (in hours,
minutes, and seconds) while the MIDI
Timepiece AV is striping SMPTE or locking to
external SMPTE time code. It also indicates
whether the MIDI Timepiece AV is synchronizing
from its own internal time base (Internal) or
locking to incoming SMPTE time code (LTC or
MTC).
DIRECT CONNECT
D CABLE X <> AE
RESET ALL DATA
D -DANGER- <E>
DATA DUMP <E>
CURRENT STATE
SYNC 00:00:00E
Internal :48000
!USB Interfaces Manual Book Page 108 Tuesday, October 10, 2000 12:43 PM
- Composite 1
- Warranty on Software 2
- Limited Warranty on Hardware 2
- MOTU USB MIDI Interfaces 3
- Contents 5
- For All Users 7
- All Users 8
- Packing List and 9
- Computer Requirements 9
- FOR ALL MOTU INTERFACE MODELS 11
- FOR MIDI TIMEPIECE AV USERS 11
- CONNECTING THE POWER CORD 11
- CONNECTING A USB COMPUTER 11
- CONNECTING MIDI GEAR 11
- MIDI CONNECTIONS WORKSHEET 13
- CONNECTING ADATS 16
- CONNECTING VIDEO 16
- CONNECTING WORD CLOCK 17
- CONNECTING AN ALESIS LRC 17
- CONNECTING A MACINTOSH 18
- WHAT NEXT? 19
- WHAT GETS INSTALLED? 21
- WHERE TO GO NEXT 21
- SMPTE Sync and MMC with a 23
- Windows Sequencer 23
- SLAVING A SEQUENCER TO SMPTE 24
- FOR FURTHER INFORMATION 25
- For XT & Micro Users 27
- XT& Micro Users 28
- Working with Presets 29
- WORKING WITH PRESETS 30
- Express XT and micro express 30
- WORKING WITH PRESETS 31
- USER PRESETS 32
- Using Micro Express Console 33
- THE TOOLBAR 34
- SMPTE frame rate 35
- WINDOWS MIDI PORTS 36
- MIDI ROUTING WINDOW 37
- USING MICRO EXPRESS CONSOLE 38
- USING MICRO EXPRESS CONSOLE 39
- FILTER WINDOW 41
- CHANNEL MAP WINDOW 42
- SYNC WINDOW 43
- TOOLBAR SYNC DISPLAY 46
- PEDAL WINDOW 48
- MAKING CLICK-TO-MIDI SETTINGS 50
- Using MIDI Express XT Console 53
- USING MIDI EXPRESS XT CONSOLE 58
- SMPTE Synchronization 73
- SMPTE SYNCHRONIZATION 74
- LTC MODE 76
- MTC MODE 77
- MIDI Machine Control 79
- SETTING MMC DEVICE ID’S 80
- SETTING UP OTHER MMC DEVICES 80
- SETTING UP A HARDWARE MMC 80
- CONTROLLER 80
- MIDI MACHINE CONTROL 81
- Part III 83
- For MTP AV Users 83
- MPT AV Users 84
- THE ADVANCED MIDI WINDOW 100
- WORKING WITH SETUPS 101
- Using the Front Panel LCD 103
- JAM SMPTE 104
- WORKING WITH BASE SETUPS 106
- BaseSetup 1 N 107
- BASE-SETUP 1 107
- Basic Studio YE 107
- WRITE OVER 1 107
- MAKING THE GLOBAL HARDWARE 109
- SETTINGS 109
- PERFORMING A MIDI DATA DUMP 110
- USING THE SMPTE CONTROLS 110
- D +00:00:00/00 E 112
- THRESHOLD 10 114
- CLICK DECAY 10 E 114
- MIDI ROUTING 116
- MUTING MIDI DATA 116
- MIDI CHANNEL MAP 116
- OUT CHANEL REMAP 117
- OUT_1CH 7 TO 1 117
- MIDI cannon 118
- Console 118
- Synchronization with the AV 119
- CHOOSING A MASTER SYNC MODE 120
- SYNCHRONIZATION WITH THE AV 121
- LOCKING TO VIDEO 122
- SLAVING ADATS 124
- SLAVING A MOTU 2408 SYSTEM 124
- Component 125
- Setting for the 125
- ADAT sync scenario 125
- I Timepiece AV a certain 127
- SYNCHRONIZATION WITH THE AV 128
- ” (starting frame) — the 131
- OVERVIEW 133
- HOW MMC WORKS 133
- MMC device ID # 134
- MTP-AV 20 E 134
- adat 1 E 134
- MMC REMOTE CONTROL OF RECORD 136
- FUNCTIONS 136
- MMC ROUTING EXAMPLE 136
- A-_ 0 B-_ 0 E 137
- PEDAL TYPE 138
- PEDAL B>LRC E 138
- Appendices 141
- Glossary 143
- APPENDIX A: GLOSSARY 144
- APPENDIX A: GLOSSARY 145
- SMPTE Synchronization Basics 147
- WHAT IS LTC? 148
- WHAT IS VITC? 148
- THE BENEFITS OF VITC OVER LTC 148
- SHOULD I USE LTC OR VITC? 148
- FRAME RATES 148
- WHAT IS DROP FRAME? 149
- WHY DOES DROP FRAME EXIST? 149
- SHOULD I USE DROP FRAME? 149
- Troubleshooting and Customer 151
- TROUBLESHOOTING 152
- CUSTOMER SUPPORT 152
- REPLACING DISKS 152
- TECHNICAL SUPPORT 152
Related products and manuals for Recording Equipment MOTU Digital Timepiece
Recording Equipment MOTU 828 User's Guide
(66 pages)
(66 pages)
Recording Equipment MOTU 8pre User's Guide
(68 pages)
(68 pages)
Recording Equipment MOTU 828 User's Guide
(82 pages)
(82 pages)
Recording Equipment MOTU 828mkII User's Guide
(110 pages)
(110 pages)
Recording Equipment MOTU 896 User's Guide
(134 pages)
(134 pages)
Recording Equipment MOTU 8pre User's Guide
(80 pages)
(80 pages)
Powiązane produkty i podręczniki dla Pompy Florabest FTP 400 C2
(46 strony)
© 2020, manymanuals.com. All rights reserved. | 0.545 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals